 |
|
|
|
|
KINGSMERE CRAFTS
HAND-CRAFTED LEATHER GOODS
Colouring Leather
Some people refer to the colouring of leather "pictures", whether carved, embossed or stamped into the leather, as paintings. Do not refer to them as such, for they are not painted.
When colour is added it is with leather dye, which requires much more care in applying than does paint. Paint is a viscous mixture, whereas leather dye is very thin (like water), and spreads very quickly, which necessitates greater care being taken in the use of leather dye. The colouring of leather is in itself an art.
However, in today's marketplace there are numerous brands of specially prepared dyes and finishes. You can use anything from acrylics, oil colours, lacquers, coloured waterproof inks to enamels and lots more besides. Water and spirit-based dyes vary in intensity and shades according to brand. Some of the more well-known are Cova dyes (available in twelve colours plus white), Spectra Shade dyes and Pro Dye. Cova dyes, being acrylic, are more viscous than the other two, and have little, if any, penetration of the leather surface.
|
|
|
|
|
|
They are opaque, and unless thinned with water, cross-dyeing is not successful, indeed, when used full-strength will not produce secondary colours. However, spirit-based dyes, such as Pro Dye, can be applied over Cova White and the shades obtained will vary according to whether the white is undiluted, or if it is, by how much.
Spectra Shade or other water-based dyes cannot be applied over Cova to give the same effect it will simply lift the white from the surface of the leather.
Some leather artists do not use dye on their carvings, for they believe it takes away from the natural beauty of the leather. A leather picture is a carving, and is done in almost the same way that a wood carver would carve a piece of wood to make a wooden picture. But where a wood carver removes some of the wood to get a three-dimensional picture, a leather carver works with a moist piece of leather, and has to depress or raise up the leather (emboss), to get the effect that he is trying to put on the leather.
A leather picture is done by first tracing a design on a moist piece of leather. Whereupon the leather which has previously been "cased" (that is, its surface has been moistened, or even, depending on the thickness, soaked in a bucket of water, then allowed to gradually, dry naturally, until it is judged by its colour to be ready to be worked upon) returns to its natural colour. The design is then cut into the leather with a swivel knife. The craftsman/artist then, using a combination of saddle stamps and modelling tools, works the design or picture into the leather until the desired effect has been achieved. This is a very slow process, requiring a lot of care and patience.
|
If you try to hurry and should make a mistake in working with leather, (which is not a forgiving material) then you must start all over again from the beginning, with a new piece of leather, for it is well-nigh impossible to correct a mistake on leather.
Contents
Links
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
|
|
|
|
|
|
